DOOSAN Forklift Truck Flash Fault Codes DTC list
DTC - POSSIBLE FAULTS - MALFUNCTIONS * - FIRST CHECK IN METHODS ELIMINATION**
12 None. Indicates the end of one pass through the list faults. NONE*. None, used at the endidentification list faults**
131 Inj1open. Open circuit gasoline injector 1, wire broken injector or defective 1 injector. TurnOnMil*. Check INJ1 wiring for open circuit SECM () A5 signal to pin A injector 1**. Switched B to pin B 12 injector 1. Check injector resistance* 1, 12-14 ohm (cold)**.
132 Inj2Open. Open circuit gasoline injector 2, wire broken injector or defective 2 injector. TurnOnMil*. Check INJ2 wiring for open circuit SECM () A8 signal to pin A injector 2. Switched B to pin B 12 injector 2. Check injector resistance 2, 12-14 ohm (cold).**
133 Inj3open. Open circuit gasoline injector 3, wire broken injector silt 3 and defective injector. TurnOnMil*. Check INJ3 wiring for open circuit SECM () Signal A4 to pin A injector 3. Switched B to pin 12 B injector 3. Check injector resistance 3, 12-14 ohm (cold)**.
134 Inj4open. Open circuit gasoline injector 4, wire broken injector or defective 4 injector. TurnOnMil*. Check INJ4 wiring for open circuit SECM () Signal A7 to pin A injector 4. Switched B to pin 12 B injector 4. Check injector resistance 4, 12-14 ohms (cold)**.
141 (14) ECTRangeLow. Refrigerant sensor failure or closed on GND. TurnOnMil*. Check the ECT sensor connector and wiring for short circuit in GND SECM (). Signal B15 Blvd. 3 to ECT Blvd SECM (GND sensor). Bl. B1 1 to Blvd. Ect SECM (GND System) pin A16, B17**.
151 (15) ECTRangeHigh. Refrigerant sensor disconnected or open circuit. (1) TurnOnMil*. (2) Delayed Engine Shutdown*. (3) Check Engine Light*. Check if the sensor connector disconnected or for open circuit SECM. Signal B15 Blvd. 3 to ECT Blvd SECM (GND sensor). Bl. B1 .1 to Blvd.**
DOOSAN Forklift Error Flash Codes list
161 (16) ECTOverTempFault. Engine coolant temperature is high Sensor. measured excessive refrigerant temperature, typical due to engine overheating.
(1) TurnOnMil*
(2) DelayedEngine Shutdown*
(3) CheckEngineLight*
Check the refrigerant system by locking the radiator for proper refrigerant level and for leaks in the system. Possible ECT closure to GND, check ECT signal wiring SECM. Signal Bl. B15 .3 to Blt ECT SECM (GND sensor). Bl B1. 1 to Blvd. SECM (GND System). Blvd A16, B17.Check the regulator for refrigerant leaks**.
171 ECT_IR_Fault. Engine coolant temperature does not change as expected.None*.Check for problems with the refrigerant system such as defective or, viscous thermostat**.
181 FuelSelectConflict. Signal conflict fuel selection ok install if both of the signals fuel selection closed to the ground. TurnOnMil**. Check connection fuel selection switch is, whether short to gnd
SECM () SIGNAL A12 pin
SECM (SIGNAL) pin A15
SECM (GND Sensor) pin B1**.
191 CamEdgesFault. No CAM signal, when the engine is like, known rotates, broken sensor crankshaft leads or defective CAM sensor. None*. Check CAM sensor connections
SECM (SIGNAL) Blvd. B10 to Blvd. 2 CAM sensor
SECM (GND sensor) Bl. Bl. To Bul. 3 CAM sensor
Switched in to the sensor sensor 12 .1 Cam
Check for defective CAM sensor**.
192 CamSyncFault. Loss of sync on CAM sensor, usually due to noise on the signal ordisconnected on CAM sensor. None*. Check CAM sensor connections SECM (SIGNAL) Blvd. B10 to Blvd. 2
CAM sensor SECM (GND sensor) Bl. Bl. To Bul. 3
CAM sensor Switched in to the sensor sensor 12 .1
Cam Check for defective CAM sensor**.
193 CrankEdgesFault. No signal crankshaft when engine is known, rotates broken, crankshaft sensor leads or defective crankshaft sensor. None*.Check sensor connections crankshaft
SECM (). SIGNAL Blvd B5 .3 to Blvd.
crankshaft sensor SECM (GND sensor) Bl. B1 .2 to Blvd.
crankshaft sensor Switched in to the sensor sensor 12 .1
crankshaft Check for defective sensor
194 Cranksyncfault. Loss of sync on crankshaft sensor, usually due to noise on signal or discontinuous connection on the sensor crankshaft. None*. Check sensor connectionscrankshaft
SECM (). SIGNAL Blvd B5 .3 to Blvd.
crankshaft sensor
SECM (GND sensor). Bl. B1 .2 to Blvd.
crankshaft sensor
Switched in to the sensor sensor 12 .1
crankshaft
Check for defective sensor**.